Craftsman 113.248510 Manual do Proprietário

rIlllSave ThisManualForFutureReferenceS _AIRSownersmanualModel No.113.248210Single Speed Band Sawwith Leg SetModel No.113.248320Two Speed Band Sawwith

ALL MODELSLIST OF LOOSE PARTS IN BAG #507968ITEM DESCRIPTION QTY.A Truss Head Screw 1/4-20x12 ... 32B Lockwasher Ext. t/4 ...

assembly and alignmentMODEL 113.248210, 113.248320,113.248440ATTACHING LEVELING FEETFrom the loose parts bag find the following hardware:Item Descript

MODEL 113.24821 O, 113.248320,1113.248440ATTACHING LEG SETFrom the loose parts bag find the following hardware:Item Description Qty.A Truss Head Bolts

..Use truss head bolts, Iockwashers, and hex nuts tomount the two (2) rear legs to the basic saw assem-bly. It may be necessary to slightly tilt the s

MODEL 113.2485102. After layout of cabinet parts, take the lower shelfand turn upside down on floor. Small front flangeshould be pointing upward.3. Lo

MODEL 113.2485106.Secure rear of shelf to right side and left side panelsusing (2) 1/4-20 x 1/2 truss head bolts and hex nuts.Hand tighten only.LOCKWA

MODEL 113.2485102. Place saw on cabinet so that holes in bottom ofsaw line up with holes in top of cabinet.3. Install bolts, Iockwashers, and nuts as

ALL MODELSATTACHING THE HANDWHEEL1. From loose parts bag find one (1) pan head screw10-32 x 2 and one (1) hex nut. Install the hand-wheel. Reach insid

MODELS 113.248320,113.248440, and113.2485104. Locate the correct motor pulley (Model 113.248210has a "one-step" pulley). Placethe shaft key

10. Install a flanged lock nut onto this motor stud.Tighten the flanged lock nuts, using a %-inchwrench, until almost tight. It will be easier to tigh

FULL ONE YEAR WARRANTY ON CRAFTSMAN BAND SAWIf within one year from the date of purchase, this Craftsman Band Saw tails due to adefect in material or

ALL MODELSCONNECTING THE MOTOR1. Next, the motor cord needs to be wired into themotor. Coming from the underside of the tablewill be a cord with a bla

MODEL 113.248320, 113.248440& 113.248510SELECTING BLADE SPEEDThe band saw has two speed settings: 3000 FPM fornormal operation and 1500 FPM for op

ALL MODELSATTACHING TRIM CAPS1. Find the left and right trim caps.2. There are two plastic stubson the back of each trimcap.3. These stubs will snap i

getting to know your band saw2TENSION ADJUSTMENT KNOBCOVER1WARNING LABELBEVELBLADE GUARDWARNINGLABEL BEVEL4BEVEL LOCK KNOBGAGESLOTBLADE GUIDESHANDWHEE

location and function of the electronic indicator systemMODEL 113.248440 & 113.248510 ON LYBATTERY COVER RELEASE SLOTS& OPEN BATTERY OPEN •BAT

FUNCTION KEYSThe five keys located to the right of the display arethe function keys. They are:io._o_ -- Turns the display "On" or "Off&

ALL MODELSINSTALLING THE BLADEWARNING: TO AVOID INJURY FROM ACCIDENTALSTARTING, MAKE SURE THE POWER CORD ISUNPLUGGED BEFORE REMOVING ANY PARTFROM THE

4. Loosen the setscrew which locks the blade guidesupport and push the support all the way back.Repeat for lower blade guide support.UPPERBLADE tl tGU

MODEL 113.248210 & 113.248320ALIGNING THE BLADE AND BLADEGUIDE ASSEMBLIESThis band saw comes equipped with a 1/4-inchblade, This band saw can be u

ALL MODELS2. Turn the upper wheel by hand a few times andnotice if the blade remains in the center of the tireon the top wheel.If the blade moves away

GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLSALL MODELS1. KNOW YOUR POWER TOOLRead and understand the owner's manual andlabels affixed to the tool.

ALL MODELS6. To insure the backup bearing is properly sup-porting the blade, push the bearing toward theblade until it almost touches it. Turn the upp

3. Locate the two (2) oval point setscrews 1/4-20 x1/2 and use an 1/8-inch hex "L" wrench to installin the two holes, as illustrated, but do

ALL MODELS10. Mount the front table to the base as follows:a. Makesurefronttablelatchesarepositioned upashigh as they will go.b. Hold the front edge o

ADJUSTING FRONT TABLE1. Adjust the front table so it is the same height as therear table as follows:a, Lay a straight edge across front table to reart

ALL MODELSlocation and function of controlsON-OFF SWITCHNOTE: The On-Off switch has a locking feature. Thisfeatu re is intended to help prevent unauth

MODEL 113.248440 & 113.248510TILTING HEAD FOR BEVEL CUT1, Unlock bevel lock by pulling outon knob locatedunder the left front edge of the table,2.

basic band saw operationALL MODELSWARNING: FOR YOUR SAFETY, COMPLY WITHALL THE SAFETY INSTRUCTIONS ON PAGES 3-5BEFORE USING THE BAND SAW.A band saw is

INSTALLING SANDING ATTACHMENTWARNING: TO AVOID INJURY FROM UNEXPECTEDSTARTING, MAKE SURE POWER CORD IS UNPLUG-GED BEFORE MAKING ADJUSTMENTS TO BAND-SA

Sears recommends the following AccessoriesCaster Set for Leg Set ... 9-22222, 9-22221Miter Gauge ... 9-29929Hold-Down

Light BulbTo replace the light bulb remove the front cover. Usea phillips screwdriver to remove the lens and replacethe bulb. The light bulb is a 25 w

additional safety instructions for band sawALL MODELSSafety is a combination of common sense, stayingalert, and knowing how your band saw works.BEFORE

trouble shooting--motorALL MODELSNOTE: Motors used on wood-working tools are particularly susceptible to theaccumulation of sawdust and wood chips and

trouble shooting -- electronicsMODEL 113.248440 & 113.248510PROBLEMINo display whenis pressed.Display showsI1PROBABLE CAUSE1. Battery incorrectlyi

trouble shooting --- electronicsMODEL 113.248440 & 113.2485t 0PROBLEMDisplay does notchange when bladespeed is changed.Display changes backand for

repair partsPARTS LIST FOR CRAFTSMAN 12-INCH BAND SAWMODEL NO'S. 113.248210, 113.248320 & 113.24844078933\4\3Always order by Part Number--Not

63642336 3438 3747t7\\\4618 19\45 44 _,_35/3738 3;'3334FIGURE 2

PARTS LIST FOR CRAFTSMAN 12-INCH BAND SAWMODEL NO'S. 113.248210, 113.248320, 113.248440 & 113.248510Always order by Part Number--Not by Key N

PARTS LIST FOR CRAFTSMAN 12-INCH BAND SAWMODEL NO'S. 113.248210,113.248320, 113.248440 & 113.248510517161418 5f928\2346

PARTS LIST FOR CRAFTSMAN 12-INCH BAND SAWMODEL NO'S. 113.248210, 113.248320, 113.248440 & 113.248510Always order by Part Number--Not by Key N

PARTS LIST FOR CRAFTSMAN 12-INCH BAND SAWMODEL NO'S. 113.248210,113.248320,113.248440 & 113.2485102928/94328 30F4,47\ I17161814242223\JJ_J333

PARTS LIST FOR CRAFTSMAN 12-INCH BAND SAWMODEL NO'S. 113.248210, 113.248320, 113.248440 & 113.248510Always order by Part Number--Not by Key N

Toavoidbeingsuddenlycaughtintheblade:1.Donotwear gloves.2. Remove all jewelry and loose clothing.3. Tie back long hair.4. Roll long sleeves above the

PARTS LIST FOR CRAFTSMAN 12-INCH ELECTRONIC BAND SAWMODEL 113.24851010FIGURE 5--PARTS LIST 23" CABINETAlways order by Part Number--Not by Key Num

NOTES51

f _,, f _AIRSownersmanualSERVICEMODEL NO.113.248210Single Speed Band Sawwith Leg SetMODEL NO.113.248320Two Speed Band Sawwith Leg SetMODEL NO.113.248

glossary of terms for woodworkingALL MODELSBevelingAn angle cutting operation through the face of theboard,CrosscutA cutting operation made across the

This power tool is equipped with a 3-conductor cordand ground type plug listed by Underwriters' Labora-tories. The ground conductor has a green j

general informationALL MODELS1. This manual is for the following Models--113.248210,113.248320,113.248440, and113.248510.All sections are labeled with

TABLE OF LOOSE PARTSITEM DESCRIPTION QTY.A Motor ......... 1B Basic Saw Assembly ...... 1(Models 113.248210 and 113.