Craftsman 358.34110 Manual do Operador descarregar pdf (Página 6)

[

4.; ,,,

....................................................

:!-+

. -+, -

j,llll iiiII

iii i I i I II ii ii i Hill

, ,ll

SPECIAL SAFETY SECTION (continued)

- IIIII I ii

- 6

A. KICKBACK SAFETY FEATURES

• -_ Reduced-Kicl_back Guide Bar+ designed with a

small radiustipwhichreduoesthesizeofthe kickback

danger zone on the bar tip. Figure 5. A Reduced

Kickback Guide Bar is one which has been

demonstrated to significantly reducethe numberand

.seriousness ofkickbacks whQn_sted inaccordance

withthe safetyrequirementsforelectricchain saws.

• assetbyU.L i662. " "--_

-- Low-Kickback Chain, designed with a contoured

depth gauge and .guard link which deflect the

-- kickback force and a!low woodto graduallyride into

the cutte_Figure 5.Low-Kickback Saw Chain ischain

•which h_s met the .kickback performance

requirements of ANSI B175.1.

-- Handgua_; designed to reduce the chance ofyourleft

hand contactinglhechain ifyour handslipsoffthe front

handlebar.

-- Position of front and rear handlebars, designed

withdistancebetweenhandleswhich providesbetter

control,balance, and msistan_:_if kickbackoccurs.

B, DOUBLE INSULATION

Your Chain Saw is double insulated to help protect

•against electdc shock. Adoubleinsulatedtool iscon.

structedthroughoutwithtwo separate "layers" of elec-

trical insulation or one double thickness of insulation

between the operator and the electrical system of tl_e +

tool.

Toolsbuiltwith thisinsulation systemare notintended

to be grounded. As a resutt, the extension cord used

i iiii ii iiiii iiiiii ii

• A, WARNING

DOnotoperatethe chain saw Unless tile safetydevices

or their specified replacements are propedy installed

and maintained according to the instructions in this

manual. Do not use any other guide barandchain com-

bination that isnot equivalent to the originalequipment

or not certified to comply with ANSI B175,1. Failure

to follow these instructions can res_ultin serious

• Figure 5

ii I I +

withyoursawcan be plugged intoany conventional 120

voltelectrical outlet withoutconcern formaintaininga

'ground connection.

-Safety precautions must be observed when

operating any electrical tool. The double insulation

system only supplies added protection against injury

resulting from a possible electrical insulation failure

withinthe saw.

• . i ii

' ' C,. POWERSOURCE AND EXTENSION. CORD

1. POWER.SOURCE

Use only._anA.C. voltage supply identical to that

....shown o n the name plate of th esaw to power this

chain saw,

WARNING

All electrical repairs to this saw, including housing,

switch, motor, etc., must bediagnosedand repaired by

your Sears Service Center. Failure to do so can cause

thedouble insulation construction to becomeineffeo-

tlve and resultin sedous injury.

lille ii iiiiii II

2.) Heavy enough to cat'rythe currentfrom the

power source to the distance at which the

saw is to be used. Otherwise, lossof power

and overheating can occur causing damage

to theunit. Refer to Figure6 for minimumwire

gauge recommendationS.

3.) In good condition. Cbi'dinsulationmust be

intact with no cracks or deterioration. Plug

connectors must be undamaged

b. Suitable extension cords are available at your

•Sea_ Retail or Catalog Store.

2, EXTENSION CORD

a. The extension cord used to reach the power

source must be:

'_+) Specifically markL_l as suitable for outdoor

Use. The suffix,W-A, mustbe included onthe

cord label.

MINIMUM WIRE GAUGE

RECOMMENDATIONS

AMP VOLTS 25 FT_ 50 FT. 100 FT. 150FT,

10.5 120 ' !8 16 14 12

A+W.G.A.W.G.A.W.G. AW.G.

Figure 6

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Comentários a estes Manuais

Sem comentários

Craftsman 358.34110 Manual do Operador Página 6

Comentários a estes Manuais

Manuais e produtos relacionados com Motosserras elétricas Craftsman 358.34110