Craftsman 315.23743 Manual do Proprietário

OWNERSMANUALMODEL NO.315.23/43SerialNumberModel and serial numbermay be found on plate atmotor end cap,You should record bothmodel and serial number i

OPERATIONREAD RULES FOR SAFE OPERATIONWARNING: DO NOT ALLOW FAMILIARITY WITHYOUR SAW TO MAKE YOU CARELESS. REMEMBERTHAT A CARELESS FRACTION OF A SECON

OPERATIONOPERATION OF MITER ARMYour miter saw will cut any angle from 0 ° to 47.1/2"left and right. To operate miter arm release lock lever(A) on

TABLE EXTENSION AND SECURING WORKPIECE (Continued)Because of the possibility of the material being cutcausing the saw blade to jam or feed itself into

TYPICAL OPERATIONS (Co,-,t,-,uod)CUTTING MOULDINGSYou can cut 45 ° miter cuts on material and moldingsup to 2.3/8" thick, See Fig, 18. Instead of

TYPICAL OPERATIONS (Continued)CUTTING THIN MATERIALSYour miter saw can be used for cutting thin materialssuch as laminated plastics and composition bo

TYPICAL OPERATIONS (Continued)CUTTING POLYGON MITERSAny closed construction has a number of sideswhich must be joined together at the proper angles.Th

TYPICAL OPERATIONS (Continued)CUTTING COMPOUND MITERS (Cont'd)To aid In making the correct settings, the compound angle setting chart shown in Fi

NOTESPage 17

MAINTENANCEWHEN SERVICING USE ONLY IDENTICAL REPLACEMENT_RARTSBRUSH REPLACEMENTDISCONNECT MITER SAW FROM POWER SUPPLY.1, Remove brush caps (A) from mo

MAINTENANCE ¢Coot nued)REMOVING THE BLADEDISCONNECT MITER SAW FROM POWER SUPPLY.1, Place saw head in the position shown in Fig. 31.Remove four screws

FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL ARM MITER SAW"If within one year from the date of purchase, this Craftsman Radial Arm Miter Saw falls

MAINTENANCETO CLEAN SAWDUST FROM TURNTABLEPeriodically sawdust will accumulate between theturntable and miter saw table, This will cause dif-ficulty i

MAINTENANCE (Continued)SAW BLADESThe best of saw blades will not cut efficiently if they are not kept clean and sharp. Using a dull blade willdo nothi

TROUBLE SHOOTINGPROBLEMSaw will not run,Mechanical brake notfunctioning.Blade does not reach fullspeed,Saw vibrates excessively.Saw makes rough cuts.M

NOTES'l Page 23

NOTESPage 24

-------- CRAFTSMAN RADIAL ARM MITER SAW -- MODEL NUMBER 315.23743SEEFIGURE"C"FOREXPLODED VIEWSEEFIGURE"B"FORjEXPLODED VIEWSEE FIGU

\\'\\'\\,\\\/II! I ! ! ! I I I!11 II I III I ... _ _-- _ I I I I! _ --L I _[_ ! ! L _ i I _.__

Key PartNo. Number1 611638-0042 622180.0013 989001-0014 621644-0065 612465-0026 941401-0237 989959-0018 621644-0029 931744-81110 989960-00111 989048-0

CRAFTSMAN RADIAL ARM MITER SAW-- MODEL NUMBER 315.237439SEENOTE12141013t15172ONOTE 1: COAT WITH LIGHTFILM OF HIGH PRESSURE GREASEFIGURE"B"Pa

CRAFTSMAN RADIAL ARM MITER SAW -- MODEL NUMBER 315.23743The Model Number will be found on a plate attached to the Motor End Cap.Always mention the Mod

RULES FoR SAFE OPERATION (Continued)9. DON'T FORCE TOOL. It will do the job better and safer for which it was design-ed.10.11.12.i3.16.17.18.19.2

CRAFTSMAN RADIAL ARM MITER SAW -- MODEL NUMBER 315.23743.1SEENOTE 3610TORQUE TO 100 INCH,/LBS. MIH; //NOTE 1: COAT WITH LIGHT FILM OFHIGH PRESSURE GRE

Key PartNo. Number1 989006-0022 703776-0983 617966-0035 621377-0046 612681-001614658-0108 611767-0029 611800-00410 621359-00011 990542-00212 622180-00

S_ A/RSOWNERSMANUALSERVICEMODEL NO.315.23743HOW TO ORDERREPAIR PARTSCRAFTSMAN7½ INCH RADIALARM MITER SAWDOUBLE INSULATEDWITH MECHANICAL BRAKNow that y

RULES FOR SAFE OPERATION (Continued)24. OUTDOOR USE EXTENSION CORDS -- When tool is used 6u_do____, use onlyextension cords suitable for use outdoors,

TOOLS HEEDED FOR ASSEMBLY AND ADJUSTMEHTYour miter saw can be assembled and adjusted with a tow be$1c hand tools shown below:?/16" AND 1/2"

FASTENING MITER SAW TO WORKBENCH OR LEGSET (9.22246)DISCONNECT MITER SAW FROM POWER SUPPLYif the miter saw Is to be used in a permanent loca-tion, it

ADJUSTMENTSYour miter saw has been factory adjusted and altgned to assure proper operation. However, misallgnmentcan occur during shipping, All alignm

ADJUSTMENTS (Con'" ued)DISCONNECT MITER SAW FROM POWER SUPPLYBLADE HEEL ADJUSTMENTThe saw blade must be aligned, front to rear, with thedire

ADJUSTMENTS Continued)DISCONNECT MITER SAW FROM POWER SUPPLYFENCE TO FENCE ADJUSTMENTAfter the left fence has been squared to the blade, orany adjustm