Craftsman 351.217030 Manual do Operador

Operator's Manual8"JOINTER ANDJOINTER STANDModel No.351.21 7030CAUTION: Read and followall Safety Rules and OperatingInstructions before Fir

CHECKING BLADE HEIGHTRefer to Figure 9.Once outfeed table is set, a straightedge can be usedto check blade height.• Follow the procedure described abo

• Support work on both infeed and outfeed tables.Over half the board must rest on tables before andafter cut to keep wood from tilting off table. Use

SYMPTOMSnipe gouging at ends ofboard)Fuzzy grainTorn grainRough raised grainPOSSIBLE CAUSE(S)1. Dull Blades2. inadequate support of long boards3. Unev

NOTES13

Model 351.217030Figure 13 - Replacement Parts Illustration for Stand2923. / 27/_"_322128 27 22 /[12\1819i25 626tl 33 I[3431t11 139/14

KEYNO.12345678910111213141516171819202122232425262728293031323334APART NO.N/A23202.0023203.0023204.00STD840812STD851008STD85101023205.0023206.0023207.

Model 351.217030Figure 14 - Replacement Parts Illustration for Jointer326/22I 3_26 2543333124 412319 35303894112913\_531816

KEYNO. PART NO.1 23240.002 STD3152413 23241.004 23242.005 23243.006 23244.007 23245.008 02661.009 STD85201010 STD84101011 23246.0012 00975.0013 23247.

Model 351.217030Figure 15 - Replacement Parts Illustration for Fence19829 8 /8 10181820/2527 6261517214\\\14\\\11 \\24\x\\18

KEYNO.123456789101112131415161718192O212223242526272829APART NO.23221.00STD87084023223.0023239.0023224.00STD84101023403.00STD870820STD84081223225.00ST

Warranty... 2SafetyRules... 2-3Unpacking... 3Assembly...

TM Sh4® Registered Trademark / Trademark / Service Mark of Sears, Roebuck and Co.® Marca Registrada / TM Marca de F_brica / SM Marea de Servicio de Se

• Userecommendedaccessories(refertopage19).Useofimproperaccessoriesmaycauseriskofinjuryto persons.• Handleworkpiececorrectly.Protecthandsfrompos-sible

MOUNT JOINTERRefer to Figure 2, page 3.• Place jointer on stand and attach it.NOTE: At least two people are required to lift the 300lb. jointer.• Join

• Secure set screws by tightening hex nuts.• Remove hex head packing bolt from top of fencebracket assembly and discard. Insert fence anglelock handle

• Use only 3-wire extension cords having 3-pronggrounding type plugs and 3-pole receptacles whichaccept the tool plug.• If the extension cord is worn,

11\12lO\1 Stand2 Push Blocks3 Start/Stop Switch4 Emergency Stop Switch5 Depth Scale and Limit Stop6 Infeed Table Hand Wheel7 Infeed Table8 Fence9 Fenc

• Maintaintheproperrelationshipsofinfeedandout-feedtablesurfacesandcutterheadbladepath.• Donotbacktheworktowardtheinfeedtable.• Supporttheworkpieceade

90° Limit Plate in 90° Limit Bolt 135° LimitDown Position and Nut Bolt and Nuts S y45° Limit Fence AngleCollar Hock HandleFigure 8 - Fence Positioning