Craftsman 320.17541 Manual do Operador

Operator's Manual9.5 Amp 1314Peak HPF=xed Base RouterModel No.320.175410(_)usDOUBLE INSULATEDCAUTION Read, understand and followatl Safety Rules

ADDITIONAL RULES FOR SAFE OPERATION cont.7o ALWAYS check the tool for damaged parts. Before further use of the tool, a guard orother part that is dama

PARTSLIST (Fig. 1)1. Fixed Baseand Motor with1/2-in.Collet/Nut (_2. SawdustExtraction Hood3. 2 Screws _p(for attaching Hood) _p4. 1/4-in. Collet/Nut5.

KNOWYOUR FIXED BASE ROUTER cont. (Fig. 2)This Fixed Base Router has the following features:1. Powerful, 9.5 Amp Soft Start Motor develops 13/4 Peak HP

KNOW YOUR FIXED BASE ROUTER cont. (Fig. 2)Dve ToolIndicator" LightMotor HousingTop CapQuick ClampMotorChangingSystemMotor HousingMilled CastAlumi

Rating,,, ,No-load Speed, i ,i ,,,,,,,,,,,,,, , , ,,,,,, ...Peak HP, ,,,, ,,,,,, i,u,,,Input, J,t,iCollets/Nuts and Cutter Bi't 's'

INSTALLING AND REMOVING THE CUTTING BIT (Figs. 3, 4 and 4a)X,,./ _,,. Nut coHetSpindle LockFig. 3INSTALLING THE CUTTER BIT1o Turn motor off and unplug

REMOVING THE CUTTER BIT (Figs. 3 and 4 see page 15)1. Turn motor off and unplug from power source_2. Remove motor from fixed base.3. Set the motor ups

INSTALLING ROUTER MOTORIN BASE (Fig. 5)t, Turn motor off and unplugfrom power source.2. Place fixed base on flat surface°3,_ With back of fixed base f

ADJUSTING DEPTH OF CUTWARNING: Your router should NEVER BE TURNED ON or be connectedto the power source when you are assembling parts, making adjustme

To Adjust Depth (Figs. 6 and 6a)2_3_4_..748_Turn motor off and unplug frompower source°Place router on a flat, level surfacewith back of fixed base fa

Warranty ... Page 2Safety Symbols ...

Deep CutsThe proper cutting depth, (for each pass), is always determined by the material,the cutter bit size and type, and the power of the motor.Alwa

LED WORKLIGHTS (Fig. 8)Your router motor has 3 built-in worklights locatedaround the collet/nut to provide high visibility ofworkpiece when cutting. T

EDGE ROUTING OR INTERNAL ROUTINGFor ease of operation and to maintain proper control, your router has two handles,one on each side of the router base.

INTERNAL ROUTING (Figs. 11, 11a, 11b and 12)1., With depth-of-cut set, tilt router and place on workpiece with leading edge of sub-basecontacting work

FREEHAND ROUTING WITH THE FIXED BASE (Fig. 13)WARNING: Do not use large cutter bits for freehand routing. Use of largecutter bits when freehand routin

EDGING WITH A PILOT BIT (Figs. 14 and 14a)The arbor-type bits with pilots are excellent for edge shaping of any workpiece edge thatis either straight,

FEEDING THE ROUTER (Fig. 15)The secret to professional routing is in making a careful set-up for the cut, selecting theproper depth of cut, knowing ho

DIRECTION OF FEED - INTERNAL CUTS (Figs. '16 and 16a)When making an internal cut, such as a groove, dado or slot, always have the guide youare us

RATE OF FEED (Figs. 17 and 17a)The proper rate of feed depends on several factors: the hardness and moisture contentof the workpiece, the depth of cut

CHIP SHIELD DEFLECTOR (Fig, 18)_-_WARNING: ALWAYS wear eye protection.The chip shield deflector is not intended as a safety guard.To remove chip shiel

The purpose of safety symbols is to attract your attention to possible dangers.The safety symbols, and the explanations with them, deserve your carefu

I ]WARNING: To ensure safety and reliability, all repairs should be performedby a qualified service technician at a Sears Service Center.GENERALOnly t

REPLACEMENT OF CARBON BRUSHES (Fig. 20)Replacement brush sets are available through Sears Parts and Repair Centers°!o Unplug the router motor before i

[z_ WARNING: The use of attachments or accessories that are not1recommended for this tool might be dangerous and could result in serious injury.ISears

In additionto a widevariety of routerbits,Sears alsooffers accessoriessuchas:Routertables,varioustemplatesets,universalrouterfencewithlock knobs (6418

9.5 Amp / 13/4Peak HP-MODEL NUMBER 320.17541The Model Number will be found on the Nameptate_Always mention the Model Number in all correspondence rega

9.5 Amp / 1314Peak HP -MODEL NUMBER 320.17541The Model Number will be found on the Nameplate_Always mention the Model Number in all correspondence reg

9.5 Amp / 1 3/4Peak HP Fixed Base Router-MODEL NUMBER 320.17541The Model Number will be found on the Nameplate,Always mention the Model Number in alt

9.5 Amp / 1 3/4 Peak HP Fixed Base Router-MODEL NUMBER 320.17541The Model Number will be found on the Nameplate,Always mention the Model Number in all

38

39

Z_ WARNING: BE SURE to read and understand all instructions in thismanual before using this router. Failure to follow all instructions may resultelect

Your HomeFor repair - in your home - of all major brand appliances,lawn and garden equipment, or heating and cooling systems,no matter who made it, no

TOOL USE AND CARE SAFETYZ_ WARNING: BE SURE to read and understand all instructions beforeoperating this router. Failure to follow all instructions li

ELECTRICAL SAFETY cont.3. BEFORE plugging in the tool, BE SURE that the outlet voltage supplied is within thevoltage marked on the tool's data pl

SERVICE SAFETYI. If any part of this router is missing or should break, bend, or fail in any way;or should any electrical component fail to perform pr

SAFETY RULES FOR ROUTERS cont.I3. MAKE SURE the cutter bit is not in contact with the workpiece before the switchis turned on.The bit must ALWAYS be r

A WARNING: Use of this tool can generate dust containing chemicalsknown to cause cancer, birth defects or other reproductive harm.Some examples of the